1. Measurement of Insulation Resistance of Lightning Arrester
Insulation resistance measurement, for the FS arrester, is mainly to check the sealing condition, if the seal is not strict will inevitably cause internal moisture, so that the insulation resistance is significantly reduced. According to the requirements of the pre-test procedure, a 2500V megohmmeter shall be tested during the measurement, and the insulation resistance measured shall not be lower than 2500MΩ. Before the test, wipe the surface of the zinc oxide arrester porcelain sleeve clean, otherwise it will affect the accuracy of the test due to leakage current on the surface of the jacket. To do this, clean the surface of the porcelain sleeve with a clean cloth with good water absorption before the test, and use a thin metal wire to wind around the lower part of the first shed of the jacket and then connect it to the “shield” terminal of the megohmmeter. Eliminate the effects of. In the test, the megohmmeter and the arrester cable should be as short as possible, and ensure good electrical contact. When testing, the megohmmeter should be placed horizontally with uniform shaking speed, and 120 rpm is appropriate for good measurement results. Lightning arrester prices For the FZ type arrester, in addition to checking whether the inside is damp, it is also necessary to check whether the shunt resistance is broken or deteriorated. If the shunt resistance is aged or broken, the insulation resistance will be increased due to poor contact. To ensure that the measurement is accurate, it should be measured twice and compared to see if there is any change in the data. Measurements should be made using the same megohmmeter of the same voltage class, otherwise they cannot be compared.
2. DC 1 mA reference voltage test
During the test, a 0.75-fold 1 mA DC voltage was applied across the zinc oxide surge arrester (with a DC voltage ripple rate of not more than ±1.5%) when the current through the arrester stabilized at 1 mA. The voltage across the arrester should not be less than 25 kV.
3. DC leakage current test
After applying a 0.75-fold 1 mA DC voltage across the arrester , the leakage current through the zinc oxide arrester should not exceed 50 μA. During the test, when the leakage current reaches 30μA, the voltage will continue to rise. At this time, the leakage current will increase dramatically. At this time, the voltage should be increased slowly. If the boost pressure is too fast, the measurement will be inaccurate. In order to prevent the influence of leakage current on the surface of the porcelain sleeve, a good cloth with good water absorption should be used to wipe the outer surface of the porcelain sleeve clean before the test to eliminate the influence.
4. Measurement of the electric conduction current of the arrester with parallel resistance lightning arrester
The micro-amperemeter used for the electric conduction current of the parallel resistance lightning arrester type measuring belt should have an accuracy of not less than 1.5, and the connecting wires should be thick and short to reduce the influence of the wire resistance on the measurement. Also pay attention to the effects of stray currents and stray capacitance around high voltages during measurement. It should not be measured with an electrostatic voltmeter. Keep the test equipment away from devices that are prone to interfering magnetic fields, or set up shielding measures. When measuring the flow of electrical current, the application of the dc test voltage should start with a sufficiently low value and then slowly increase, apply the voltage in segments and read the value of the electrical conduction current in segments. After the voltage to be tested remains at the specified time, if the microampere meter pointer is not shaken, its display value is the electric conduction current value of the voltage. If the parallel resistance is aged and the contact is poor, the electric conduction current is significantly decreased. If the parallel resistance is broken, the electric conduction current is reduced to zero. If the parallel resistance itself is flooded, the electrical current will increase dramatically, typically up to 1000μA. In order to ensure the safety and accuracy of the number of high-voltage arrester tests, it is also necessary to compare the measured values ​​of the electric conduction currents at different temperatures and convert them to the same value of the electric conduction current value. Experience has shown that for every 10°C increase in temperature, the electrical conduction current increases by approximately 3% to 5%.
This article Source: Zinc Oxide Arrester Test http://?id=134
Line lightning arrester http:// lightning arrester sheath http://
Drop arrester http:// arrester online monitor
Arrester Online Monitor http:// Zinc Oxide Arrester
Zinc Oxide Arrester Model http://?id=1
Zinc Oxide Arrester Parameter http://?class_id=1
Lightning Protection Technology http://?id=53
Lightning knowledge http://?class_id=4
Zinc Oxide Arrester Parameter http://?id=126
Metal oxide arrester http://?class_id=1
Zinc Oxide Arrester Test http://
Zinc Oxide Arrester Installation http://?id=100
Arrester Standards and Specifications http://?id=101
Zinc Oxide Arrester Principle http://?id=8
The role of zinc oxide surge arrester http://
Zinc Oxide Arrester Installation http://?id=111
Zinc Oxide Arrester Installation http://
Zinc Oxide Arrester Parameter http://
Zinc Oxide Arrester Model http://?id=97
Arrester parameters http://
China Electric Equipment Network provides support

Household Ladder- D type tube Household Ladder

The model of household ladder, more steady with D type aluminum tube , with anti-slip . aluminum frame in front and back is strong and stable . Easy folding and extending .It`s lightweight and portable aluminum design.It conforms to EN131. The max load of Household ladder is 150KGS.

In addition, the household ladder could be a new tool - clothes hanger . See the details as follows .

Features:
1.Anti-slip feet
2.Double rivet construction.
3.Thickening extrusion, strong anti-rust.
4.Advanced technology of auto-locking knobs.
Specifications:
1.Fashion and durable
2.The use of advanced technology, manufacture
3.High quality perfect service
4.Steel Foldable Stool
5.Light Weight
6.Wide step,comfortable to stand and sit.
Portable folding stainless steel Step Ladder:
1.Stainless steel material is more durable and stronger.
2.With CE certificaton.

Household D Type Ladder

Household D Type LadderHousehold D Type Ladder

Household D Type Ladder

Household D Type Ladder

Household D Type LadderHousehold D Type Ladder

FAQ:

Q: Are you factory or trading company ?

A: We are factory , exported foreign over decade with rich experiences .

Q: We can change the color of the rubber cover ?

A: yes , the regular is black , you also choose other color .

Q:What`s the MOQ ?

A: 100 PCS.

Q: Can I have a sample ?

A: It`s ok .

Q:What`s your price ?

A: It`s depends on your demands, quantity , we can offer you lowest price .

Q:What`s your delivery time ?

A: Sample order : 3days , bulk order : 23-25days .

Q: Can we use our logo or brand on the package ?

A: yes , OEM is ok .

Q: What`s the payment :

A: (1) T/T: 30% deposit be paid in advance , the 70% of total payment see the copy of B/L.

(2) L/C it`s ok .

  (3) Cash also ok .

 

 

More inquires or questions , plz feel free to contact us !

Welcome to visit our factory !



Household D Type Ladder

Household D Type Ladder,Aluminum Household D Type Ladder,D Type Household Aluminium Ladder,Type D Stainless Steel Household Ladder

Yongkang Aoyi Industry&Trade Co., Ltd. , https://www.aoyiladder.com